Char-Broil 466611012 C-22G0S Betriebsanweisung

Assembly instructions © 2011PRODUCT GUIDEMODEL 466611012C-22G0S© 2011 Char-Broil, LLC Columbus, GA 31902Printed in China For support and to regis

10 6.Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, result

11Safety TipssBefore opening LP cylinder valve, check the coupling nut for tightness.sWhen grill is not in use, turn off all control knobs and LP cyli

12 CAUTIONIf burner does not light, turn knobs to OFF, wait 5 minutes, and try again. Always close valve during the 5 minute waiting period. If the

13CAUTIONSPIDER ALERT!GAS COLLECTORBOX & IGNITORVALVEBURNERVENTURILIFT OUTBURNER ASSEMBLYAIRSHUTTERSPIDER WEBSINSIDE VENTURISPIDER WEBSINSIDE VENT

14This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this

15 PARTS LISTNOTE: Some grill parts shown in the assembly steps may differ slightly in appearance fromthose on your particular grill model. However,

PARTS DIAGRAM16WNCCDEBPOTSQRIHGGGHHKBBEEAAZYXFFUFLMJVIJKCADD

1□ Place upper left leg and upper right leg as shown.□ lower legs into upper legs. FitLower Right legUpper Right legRed labelsASSEMBLY17 2Back br

1834 Place front panel between legs. Hook the slots to the preassembled #10-24x3/8’’ machine screws. Tighten the screws. Turn assembly upside

19 5 6 Stand cart upright. Hook tank exclusion wire onto the right hole on front panel. Flex tank exclusion wire to insert other end into the h

TABLE OF CONTENTSFor Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Use and Care . . . . . . . . . . . . . . .

207 In front, place control panel assembly between upper legs, and slide the slots on control panel onto the preassembled #10-24x3/8’’ machine scr

21 Ignitor Wire9 Place burner assembly into firebox as shown. Fasten the burner assembly to firebox using 5x15 fiber washers and #10-24 wing nu

11 Attach handle to lid with two 7x25 fiber washers, two 5x15 fiber washers and two #10-24 wing nuts. Place lid assembly onto firebox, align h

23 13 Hang grease cup clip from bottom of firebox, and place grease cup into grease cup clip.14 Insert tank retainer into left legs. Rota

15Tank collar opening must face the front of the grill. Set bottom of tank into notches of tank bracket. Lean tank inward and engage tank collar with

25 DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.EmergenciesProblemGas leaking from cracked/

26Troubleshooting (continued)ProblemBurner(s) will not light using ignitor.Burner(s) will notmatch light.Low flame, drop in gas flow.Flames blow out.

27 First Name | Nombre | Prénom Initial | Inicial | Initiale Last Name | Apellido | Nom de FamillieAddress (number & street) | Dirección (número

3 WARNINGCALIFORNIA PROPOSITION 651. Combustion by-products produced when using this product contain chemicals known to the State of California to ca

4First Time UseRead your Assembly Manual and ensure the grill is put together properly. Remove all Point-of-Purchase advertising material from all gr

5Outdoor grilling is really quite simple. You'll succeed with burgers, dogs, or steaks usually on your very first try. With experience, you wil

6 Cooking on your new grill is a hands-on experience, and it is recommended to remain outside with your grill while cooking. Grilling can be affec

7Why Clean?We've all heard the saying 'An ounce of prevention is worth a pound of cure'. This is great advice when it comes to keeping

8• NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full.• An over filled or imp

9 WARNINGIf “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department!Connecting Regulator to t